Thank you for the photos and that information, and based on those photos, what you will need to do is replace the awning arm altogether. For the 69 inch wall mount, the correct part is the following:
- Solera 69" Standard Flat Awning Support Arm, Black # LC281154
I have added a link below to a video review for you to check out as well if you'd like to take a look. view full answer...
The Bearing Kit # BK3-300 is the correct kit for your 2021 Keystone Outback 328RL having the Dexter D52 axle. Thank you very much for including the image of your axle as we are able to verify the correct sizes based on the tag. You will need one kit per hub or 4 for both your axles on your trailer. view full answer...
I can't quite tell from the pictures I found, but it does look like the # MC44AB1 matches the clearance lights on your 2017 Keystone Outback 278URL. Assuming they're the same, you can use the Replacement Amber Lens for MC44 or MCL44 Series Side Marker or Clearance Trailer Lights # A44AB.
You don't really need to replace the light unless it is in bad shape. However, the cost for a new light vs. the replacement lens is negligible so it wouldn't hurt to swap them out. You could also buy... view full answer...
The hitch ball for the 16K Equal-i-zer Weight Distribution System w/ 4-Point Sway Control # EQ64FR can actually be found as part # EQ54FR and is rated for 16,000 lbs just like the weight distribution system.
This same hitch ball is likely used for some of the lower-rated systems from Equal-i-zer as well. Basically if the system comes with a 2-5/16" hitch ball and isn't rated for more than 16K it likely has this hitch ball.
Attached are some review videos for you to check out. view full answer...
You sure can get Global Link G315 keys for your 2012 Keystone Outback. All you need is the Replacement Key for Global Link RV Locks - 315 # 295-000041.
You can order as many of these keys as you like to ensure you have extras if need be. On the product page simply enter however many you want in the "Quantity" box and you're set! view full answer...
The main advantage you get from switching to a higher load range on your trailer tires is an increased weight capacity. As long as the capacity of the tires are adequate for the weight of your trailer, you won't really gain much by switching to a higher load range. It is possible the tires would run slightly cooler if overrated, but even load range D tires would be overrated for your trailer.
Although we do not have any 205/75-14 tires with an E load range, we do have the Karrier ST205/75R14... view full answer...
I contacted the manufacturer with the information you provided from the sticker on your 2020 Keystone Outback Solera Awning. They advised me the information is for the fabric itself and does not provide any information for the arms. In speaking with them and giving them the size of your awning they advised me the replacement pitch arm is either going to be Replacement Pitch Arm Assembly for Solera 69" Standard Flat Awning Support Arm - Black Item # LC375994 or the Replacement Pitch Arm... view full answer...
From what I've been able to determine, your axle is a AL/KO 4400 lb axle, which would use a 10 x 2-1/4 inch brake assembly.
Dexter offers a set of self adjusting brake assemblies, part # K23-478-479 that would be compatible, but I'd like you to measure the bolt hole spacing of your brake mounting flanges, just to be sure. If the top holes are 2-7/8 inches apart and the bottom are 3-1/4 inches apart as shown in the provided photo, then the # K23-478-479 would work for you. view full answer...
The switch would work fine on a 25A circuit.
The 40A rating simply means the switch itself can handle up to 40 amps running through it without being damaged. You can use a higher rated switch without issue, but you couldn't use a lower rated switch on a circuit carrying more amperage than the switch is rated for. In other words, you can go one way, but not the other.
The switch fits rough openings measuring 1.85 inches tall x 1.20 inches wide. I'll provide a photo showing the pinout... view full answer...
We have exactly what you are looking for.
The correct replacement head assembly for your Reese Strait-Line Weight Distribution Hitch # RP66130 is the Replacement Head for Reese Weight Distribution System - Trunnion Bar # RP58167.
Now this assembly does not include a hitch ball so you will also need 2" hitch ball # A-90 or 2-5/16" hitch ball # 19286 to match the coupler on your trailer.
I included videos of the products mentioned for you to take a look at. view full answer...
We have two options for a switch matching your 3/4" x 1/2" dimensions. For white you need the # 37213645 and for black the # 37212815. These have cutout dimensions of 0.745" tall x 0.5" wide and the actual switch dimensions are 0.756" tall x 0.508" wide. view full answer...
Go To Results